Sangfor NGAF IPsec VPN not create

Newbie676529 Lv1Posted 04 Mar 2024 20:10

Last edited by Newbie676529 04 Mar 2024 20:13.

Hi There,

I have two NGAFs in HA (active - passive).
License available - Expiration Date: Never, Branch VPN Sites: 10, Lines: 10. Version: 8.0.47
I can’t select an interface in Basic Settings > VPN Paths > +Add
The Add item is not active.
How can I activate it?

Thanks.

vpn01.jpg (85.08 KB, Downloads: 118)

vpn01.jpg

Newbie517762 has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

HiHi,

Please review the below regarding your SSLVPN License Activation.

Please find the attached file for the License Activation Method.
License Activation Method.pdf (167.76 KB, Downloads: 126)
Is this answer helpful?
Newbie676529 Lv1Posted 05 Mar 2024 13:43
  
Hi, friends.
I have administrator rights to create a VPN.
The licenses are activated and the service is enabled.
This is the first VPN.
NGAF overloaded.

vpn02.jpg (67.95 KB, Downloads: 111)

vpn02.jpg
Newbie676529 Lv1Posted 05 Mar 2024 16:49
  
Hi, friends.
Overloaded (restart ) physically .
I couldn't find any IPsec VPN settings in Cli.
There is only: Sangfor_NGAF_v8.0.47_User Manual_EN.pdf

vpn05.jpg (35.88 KB, Downloads: 107)

vpn05.jpg
Newbie676529 Lv1Posted 06 Mar 2024 12:17
  
Last edited by Newbie676529 06 Mar 2024 12:36.

Last edited by Newbie676529 06 Mar 2024 12:28.

Hi,
Check if you have have the wan interfaces:
-  Enable VPN Service - Yes
- Internet works  and set Next-Hop IP
- License 10 use 0
- There is no new version 8.0.47
- My scheme in Knowledge Base"SANGFOR_NGAF_v8.0.47_IPSec VPN Active and Standby Configuration guide"

VPN07.JPG (52.71 KB, Downloads: 70)

VPN07.JPG

Vpn08.JPG (38.26 KB, Downloads: 69)

Vpn08.JPG
Newbie676529 Lv1Posted 06 Mar 2024 18:45
  
The problem is High Availability (HA).
Turned off physically Active.
In Passive, the Add+ button has become active.
But without Active it does not allow you to make changes to the settings.
Newbie676529 Lv1Posted 06 Mar 2024 19:36
  
Solution:
Lower the priority of Active in the cluster to 20.
In passive, make it active - Preemption: ON.
Add "VPN Paths".
Then return the cluster to its original active - passive state.
Newbie676529 Lv1Posted 07 Mar 2024 15:58
  
Topic - Close

Swap active – passive. Add "VPN Paths". Then return the cluster to its original active – passive state.
There are no problems with the license.

I Can Help:

Change

Moderator on This Board

0
2
4

Started Topics

Followers

Follow

67
14
3

Started Topics

Followers

Follow

3
0
2

Started Topics

Followers

Follow

1
131
3

Started Topics

Followers

Follow

Board Leaders