Sangfor Community»Categories Product Network Secure with next version(NGAF) Sangfor NGAF IPsec VPN not create

Sangfor NGAF IPsec VPN not create

views: 1690 | comments: 20 | added to Favorites 0
Lights on | 提示:支持键盘翻页<-左 右->
    组图打开中,请稍候......
Created: 04 Mar 2024 20:10

Summary:

Last edited by Newbie676529 04 Mar 2024 20:13. Hi There, I have two NGAFs in HA (active - passive). License available - Expiration Date: Never, Branch VPN Sites: 10, Lines: 10. Version: 8.0.47 I c ...

Reply

Newbie290036 Posted 11 Mar 2024 13:46
To activate the interface selection in Basic Settings > VPN Paths > +Add within your NGAF High Availability (HA) environment with Version 8.0.47, ensure that the interface you want to select is operational and not experiencing any hardware or software issues. Verify firewall rules and configuration settings, update to the latest firmware version, clear browser cache and cookies, and try accessing the configuration through the console.
Newbie676529 Posted 07 Mar 2024 15:58
Topic - Close

Swap active – passive. Add "VPN Paths". Then return the cluster to its original active – passive state.
There are no problems with the license.
Tayyab0101 Posted 07 Mar 2024 15:11
i believe you should have your solution by now.
Prosi Posted 06 Mar 2024 21:29
Please input the correct Gateway ID and verify if the device has a license because you can't activate it if no license have been bought.
Newbie676529 Posted 06 Mar 2024 19:36
Solution:
Lower the priority of Active in the cluster to 20.
In passive, make it active - Preemption: ON.
Add "VPN Paths".
Then return the cluster to its original active - passive state.
Newbie676529 Posted 06 Mar 2024 18:45
The problem is High Availability (HA).
Turned off physically Active.
In Passive, the Add+ button has become active.
But without Active it does not allow you to make changes to the settings.
Farina Ahmed Posted 06 Mar 2024 15:29
If the interfaces are properly configured and still inactive in the VPN Paths section, consider checking for any configuration errors or conflicts that might prevent their selection. Ensure that the license limitations are not exceeded, particularly in terms of the allowed number of VPN paths.
pmateus Posted 06 Mar 2024 00:36
Hi,
Check if you have have the wan interfaces configured and Enable VPN Service ?
Enrico Vanzetto Posted 05 Mar 2024 23:32
Hi, as i see in previous answers it's not a licence issue. have you double check that the interface you want to use has to be up and active? Please, in order to understand better your scenario, explain your network scenario (interfaces used, ip address NGAF, NGAF software version).Have you already tried to factory reset the device?Do you have already update Sangofr NGAF to latest version?

If you need to perform a factory reset on your Sangfor NGAF (Next-Generation Application Firewall), follow these steps:

WebUI Method:
Log in to the WebUI of your NGAF.
Navigate to Maintenance > Backup/Restore.
Click on Restore Factory Default.
Sangfor Firmware Updater Method:
Download the Sangfor Firmware Updater and install it on a PC.
Connect the PC directly to the NGAF port.
Launch the updater and search for the NGAF’s IP address.
Verify that the inserted IP matches the correct one.
If there’s a discrepancy, it might be a user input error.
If needed, reach out to Sangfor’s technical support for further investigation.
Resetting Admin Password:
If you’ve forgotten the admin password or it has been changed by someone:
Create an empty text file named reset-password.txt or copy the existing reset-password.txt file to the root directory of a USB drive.
Insert the USB drive into the NGAF device.
Restart the NGAF device.
When the device can normally log in to the WebUI, remove the USB drive.
Check the results in the reset-password.log file on the USB drive:
If the recovery is successful, record the restored console password.
Otherwise, the log will indicate recovery failure.
Notes:
The reset-password.txt file can be created directly on a Windows system.
Ensure the file is in the root directory of the USB drive.
The USB drive can have a single or multiple partitions. For a single partition, the format must be FAT32. For multi-partition drives, the text file should be in the first partition, which must also be formatted as FAT32.

Instead,to update your Sangfor NGAF (Next-Generation Application Firewall), here are the steps you can follow:

Check Firmware Upgrade Path:
Visit the Sangfor self-service portal.
Navigate to the download section and select NGAF.
Download the latest version of NGAF (e.g., version 8.0.47).
Download Sangfor Updater:
From the same download menu, select tools.
Download the Sangfor Updater.
Prepare for Firmware Update:
Log in to the NGAF management interface.
Make sure the port required for firmware updates is available.
Update the Firmware:
Use the downloaded Sangfor Updater to perform the firmware update.
Newbie517762 Posted 05 Mar 2024 09:20
HiHi,

Please review the below regarding your SSLVPN License Activation.

Please find the attached file for the License Activation Method.
License Activation Method.pdf (167.76 KB, Downloads: 126)