Cannot Get More SSO Users

Denny Chanditya Lv2Posted 28 Aug 2023 13:38

Hi,

We have several IAG 5000 series, that setup with the SSO / MS AD Domain so the Sangfor can get username for the IP, rather than only the IP Address.
Our issue is the IAG only read several users with username on the tab Users, we was check the connectivity is OK, ask the principal and use the Mirror interface for read users list but it still cannot work properly. only few users are show

is there any troubleshooting or any test that i need to do? on other IAG was works normally it can read the users from AD.

Thanks.

Zonger has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

Troubleshooting the issue of the Sangfor IAG 5000 series not properly retrieving usernames from the Active Directory (AD) for some users can involve several steps to identify and resolve the problem. Here's a systematic approach to help troubleshoot the issue:
  • Review Configuration: Double-check the configuration settings on the IAG 5000 series that is experiencing the issue. Compare it with the configurations of the IAG units that are working correctly. Ensure that the settings related to SSO and AD integration are consistent.
  • Verify Connectivity: Ensure that the IAG unit can properly communicate with the Active Directory. Test the connectivity by pinging the domain controllers and ensuring that DNS resolution is working correctly.
  • Check AD Integration: Review the integration between the IAG unit and the Active Directory. Verify that the LDAP configuration settings, including the domain name, domain controllers, and authentication credentials, are accurate.
  • Check for LDAP Issues: Monitor the IAG's logs or diagnostic information for any LDAP-related errors or warnings. LDAP authentication issues could potentially prevent the retrieval of usernames.
  • Check User Attributes: Confirm that the users for whom usernames are not being retrieved have the necessary attributes in the Active Directory. The IAG might rely on specific attributes to identify users.
  • Test with Different Users: Experiment with different user accounts to determine if the issue is specific to certain users or applies to a broader range. This can help narrow down whether it's a configuration problem or an issue with particular user accounts.
  • Check for Account Lockouts or Expiry: Verify that the affected user accounts are not locked out or expired in the Active Directory. Account status issues could prevent successful authentication.
  • Mirror Interface Configuration: Since you've mentioned using the Mirror interface, ensure that it's properly configured to capture the necessary traffic. Check for any limitations or settings that might impact the traffic monitoring process.
  • Test Different Interfaces: If possible, test using different interfaces to retrieve user information. This can help identify whether the issue is specific to the Mirror interface or is more widespread.
  • Update or Firmware Check: Ensure that the IAG unit is running the latest firmware or software updates. Sometimes, updates can address known issues or improve compatibility.

Is this answer helpful?
Farina Ahmed Posted 05 Sep 2023 13:35
  
When you're experiencing issues with an IAG (Internet Access Gateway) appliance not properly retrieving user information from Active Directory (AD) for Single Sign-On (SSO), there could be several reasons behind it. Troubleshooting this issue may involve checking various aspects of your configuration and network environment. Here are some troubleshooting steps and tests to perform:

Check Active Directory Integration:
Ensure that your IAG appliance is properly integrated with your Active Directory domain. This includes verifying that the configuration settings for AD integration are correct, such as the domain name, LDAP server details, and user search base.

User Permissions:
Ensure that the IAG appliance has the necessary permissions to query the Active Directory. The service account or credentials used for AD integration should have read access to the necessary AD attributes for user identification.

Check User Accounts:
Review the user accounts in Active Directory. Ensure that the users who are not appearing in the IAG's user list have their accounts and attributes properly configured in AD, including the attribute that the IAG uses for identifying users.

LDAP Connectivity Test:
Use a tool like ldapsearch or a similar LDAP testing tool to verify that the IAG appliance can successfully connect to and query the Active Directory server. Test the LDAP connectivity using the same settings as configured in the IAG.

Example LDAP test command:

ldapsearch -x -H ldap://your_ad_server -b "ou=Users,dc=example,dc=com" -D "cn=admin,dc=example,dc=com" -W
Replace the placeholders with your actual LDAP server details.

Logging and Debugging:
Enable and review logs on the IAG appliance for any error messages or clues about the issue. Look for logs related to the AD integration and user identification process. Increasing the logging level may provide more detailed information.

Firewall and Network Configuration:
Verify that there are no firewall rules or network issues that might be blocking or disrupting communication between the IAG appliance and the Active Directory server.

Mirror Interfaces:
Ensure that the IAG appliance is properly configured to mirror traffic to the interfaces where AD authentication is taking place. Sometimes, not mirroring the correct interface can lead to user identification issues.

Software Updates:
Check if there are any firmware or software updates available for your IAG appliance. Updating to the latest version may resolve known issues or bugs.

Compare Configurations:
Compare the configuration of the problematic IAG appliance with those of the working ones. Ensure that there are no discrepancies or missing settings.

Contact Vendor Support:
If the issue persists and you've exhausted your troubleshooting efforts, consider reaching out to Sangfor's support or the vendor's support for assistance. They may have specific knowledge and tools to diagnose and resolve the issue.
jerome_itable Lv2Posted 05 Sep 2023 08:11
  
When you're facing issues with Sangfor IAG (Internet Access Gateway) not properly retrieving user information from Microsoft Active Directory (AD) for Single Sign-On (SSO), there are several troubleshooting steps and tests you can perform to diagnose and potentially resolve the problem. Here's a step-by-step approach to address this issue:

    Check Network Connectivity:
        Verify that the Sangfor IAG appliance has proper network connectivity to the Active Directory server. Ensure DNS resolution is working correctly.

    Review Configuration:
        Double-check the configuration settings on the Sangfor IAG:
            Ensure that the AD integration settings are correctly configured, including the LDAP server information.
            Verify that the AD integration account used by Sangfor IAG has the necessary permissions to query AD for user information.
            Check for any errors or misconfigurations in the Sangfor IAG settings related to SSO and AD integration.

    Test LDAP Connectivity:
        Use a tool like ldapsearch or ldp.exe to manually test the LDAP connectivity from the Sangfor IAG appliance to the AD server. This will help ensure that the Sangfor IAG can reach the AD server and query user information.

    Check User Permissions:
        Confirm that the users who are not being properly recognized by Sangfor IAG have the necessary AD permissions and group memberships to be queried by the IAG.

    Check User Attributes:
        Ensure that the necessary user attributes (e.g., sAMAccountName) are configured correctly in the Sangfor IAG settings to map AD users to their usernames.

    Check AD Group Membership:
        If the Sangfor IAG relies on AD groups for user authentication, verify that the users experiencing issues are members of the correct AD groups.

    Logs and Error Messages:
        Check the Sangfor IAG logs for any error messages or warnings related to AD integration. These logs can provide valuable insights into what might be going wrong.

    Active Directory Health:
        Verify the health of your AD server. Ensure it is functioning properly and responding to LDAP queries.

    Test on a Different IAG:
        If other IAG appliances are working correctly with AD integration, try to replicate the configuration on the problematic IAG to see if the issue persists. This can help determine if the problem is specific to the appliance or its configuration.

    Firmware/Software Updates:
        Ensure that your Sangfor IAG appliance is running the latest firmware or software updates. Sometimes, issues can be resolved by updating to a newer version that includes bug fixes and improvements.

    Contact Sangfor Support:
        If you've tried all the troubleshooting steps above and the issue still persists, it may be necessary to contact Sangfor's technical support for further assistance. They may be able to provide specific guidance and solutions based on the version of the IAG software you are using.

Remember to document any error messages or issues encountered during the troubleshooting process, as this information can be valuable when seeking support from Sangfor or other IT professionals familiar with the IAG appliance.
Carem Lv2Posted 04 Sep 2023 15:22
  
Verify that the Sangfor IAG appliance is using the correct LDAP port (usually 389 for LDAP and 636 for LDAPS) and the appropriate encryption settings (e.g., SSL/TLS) as required by your AD setup.
Rica Cortez Lv2Posted 04 Sep 2023 15:21
  
Review the event logs and diagnostics on the IAG appliance for any error messages or warnings related to AD integration. These logs can provide valuable information about the issue.
babeshuka Lv3Posted 04 Sep 2023 15:20
  
Check firewall rules and security policies on the IAG appliance and AD domain controllers. Ensure that there are no restrictions preventing communication.
LucyHeart Lv3Posted 04 Sep 2023 15:19
  
The user accounts in your AD should have the necessary attributes populated. The attributes used for SSO may include "sAMAccountName" (commonly used for usernames) and "userPrincipalName" (often used for user login names).
Verify that the user objects in AD have accurate and unique values for these attributes.
grayice499 Lv2Posted 04 Sep 2023 15:18
  
Ensure that the LDAP bind account used by the Sangfor IAG appliance to connect to AD has sufficient permissions to read user and group information.
Double-check that the bind account credentials are accurate and have not expired.
Happpy Lv3Posted 04 Sep 2023 15:14
  
Ensure that your IAG appliance is running the latest firmware or software updates. Sometimes, software updates can address known issues with AD integration.
Fuji12 Lv3Posted 04 Sep 2023 15:12
  
Make that the IAG unit can effectively communicate with Active Directory by checking connectivity. Ping the domain controllers to check connection and make sure DNS resolution is functioning properly.
Verify AD Integration: Examine how the IAG unit and Active Directory are integrated. Check the accuracy of all LDAP setup parameters, including the domain name, domain controllers, and authentication information.
soneosansan Lv3Posted 04 Sep 2023 15:11
  
Review Configuration: On the IAG 5000 series that is having the problem, double-check the configuration parameters. Contrast it with the setups of the IAG units that are operating well. Make sure that the SSO and AD integration settings are consistent.

I Can Help:

Change

Moderator on This Board

15
21
3

Started Topics

Followers

Follow

Board Leaders