Sangfor NGAF reset

Newbie327164 Lv1Posted 27 Jul 2022 15:46

How do you factory reset a Sangfor NGAF?
Password forgotten.

jetjetd has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

Hello have you tried the steps below?

1. Connect to NGAF with firmware updater.
2. Press F10, and choose the Restore Factory Defaults.
Is this answer helpful?
Osama Muhammad Lv3Posted 08 Aug 2022 08:56
  
Steps :

Reset Password with USB drive.

1. Create an empty text file named reset-password.txt in the root directory of U Disk ( Directly in the USB)
2. Insert the USB drive to either USB ports of NGAF at front side where are eth ports and then restart your NGAF.
3. When the NGAF can normally log on to the Web User Interface, pull out the USB Drive.
4. See the results of the USB drive file reset-password.txt, If the recovery is successful, record the restored password in the file. (logs in file created) , otherwise the log is recorded the recovery failure information as unsuccessful.
Noman Rajput Lv2Posted 04 Aug 2022 14:04
  
Simplest way just connect the NGAF Firewall to firmware updater, PRess F10 and select restore factory defaults
isabelita002 Lv3Posted 04 Aug 2022 09:08
  
1. In the root directory of U Disk, create a blank text file called reset-password.txt ( Directly in the USB)

2. Restart your NGAF after inserting the USB drive into one of the USB ports located near the eth ports on the front of the device.
3. Take remove the USB Drive when the NGAF can ordinarily log on to the Web User Interface.

4. Check the USB drive file reset-password.txt for results, and if the password recovery was successful, write down the new password in the file. (logs in file produced), otherwise the recovery failure information is noted in the log as failed.
Farina Ahmed Lv5Posted 03 Aug 2022 15:15
  
Factory restore is a good option but what if in case you are working in production network and you have already configured NGAF then in that case first make a backup copy or if not possible then do the whole task of factory restore in Off hours/days so it may not affect the whole network.
Rashley Lv2Posted 02 Aug 2022 09:16
  
1. Use a firmware updater to connect to your NGAF.


2. Then, while holding down F10, select Restore Factory Defaults.
Ashley Anne Lv2Posted 02 Aug 2022 09:12
  
1. Connect to your NGAF using a firmware updater.

2. Then, pressing F10, select Restore Factory Defaults.
Rhebie Lv3Posted 02 Aug 2022 09:05
  
Connect to Updater first, then press F10 and choose restore defaults.
Pat Lv4Posted 02 Aug 2022 08:32
  
1. You should Connect to your NGAF with an firmware updater.
2. Then press F10, choose the Restore Factory Defaults.
Faisal P Posted 01 Aug 2022 21:21
  
Connect to NGAF with firmware updater. 2. Press F10, and choose the Restore Factory Defaults
kmrnliaqat Lv3Posted 01 Aug 2022 16:08
  

You can use a cross cable to restore factory defaults except by Updater,
Steps:
1. Use the power button to shut down the IAM device.
2. Prepared a cross cable.
3. Using the cross cable to connect to any two interfaces of the IAM device。(Attention: The two interface can't be bypass interfaces.)
4. Finally starting up the IAM device and waiting for 5 minutes.

I Can Help:

Change

Moderator on This Board

1
131
3

Started Topics

Followers

Follow

18
8
0

Started Topics

Followers

Follow

Board Leaders