Here is a step-by-step guide on how to implement InterVLAN routing on Sangfor:

First, you need to configure the VLANs that you want to use. Go to the VLAN configuration page in the Sangfor management interface and create the VLANs that you need. For example, you might create VLAN 10 for the finance department and VLAN 20 for the marketing department.

Next, you need to configure the VLAN interfaces. Go to the interface configuration page and create a new interface for each VLAN that you created in the previous step. For example, you might create Interface 1 for VLAN 10 and Interface 2 for VLAN 20.

Assign IP addresses to each interface that you created. For example, you might assign IP address 10.0.1.1 to Interface 1 and IP address 10.0.2.1 to Interface 2.

Now you need to configure the routing between the VLANs. Go to the routing configuration page and add a new static route for each VLAN. For example, for VLAN 10 you might add a route for the 10.0.2.0/24 network with a next hop of 10.0.1.2 (the IP address of the router interface that connects to VLAN 20). Similarly, for VLAN 20 you might add a route for the 10.0.1.0/24 network with a next hop of 10.0.2.2 (the IP address of the router interface that connects to VLAN 10).

Finally, you need to configure the router interfaces that connect to each VLAN. Go to the router interface configuration page and configure each interface with an IP address that is in the same subnet as the VLAN interface that it connects to. For example, if Interface 1 has IP address 10.0.1.1, then the router interface that connects to Interface 1 should have an IP address in the 10.0.1.0/24 subnet.

With these configurations in place, hosts on each VLAN should be able to communicate with each other through the router, and you should have InterVLAN routing set up on your Sangfor device.

Here is a step-by-step guide on how to implement InterVLAN routing on Sangfor:

First, you need to configure the VLANs that you want to use. Go to the VLAN configuration page in the Sangfor management interface and create the VLANs that you need. For example, you might create VLAN 10 for the finance department and VLAN 20 for the marketing department.

Next, you need to configure the VLAN interfaces. Go to the interface configuration page and create a new interface for each VLAN that you created in the previous step. For example, you might create Interface 1 for VLAN 10 and Interface 2 for VLAN 20.

Assign IP addresses to each interface that you created. For example, you might assign IP address 10.0.1.1 to Interface 1 and IP address 10.0.2.1 to Interface 2.

Now you need to configure the routing between the VLANs. Go to the routing configuration page and add a new static route for each VLAN. For example, for VLAN 10 you might add a route for the 10.0.2.0/24 network with a next hop of 10.0.1.2 (the IP address of the router interface that connects to VLAN 20). Similarly, for VLAN 20 you might add a route for the 10.0.1.0/24 network with a next hop of 10.0.2.2 (the IP address of the router interface that connects to VLAN 10).

Finally, you need to configure the router interfaces that connect to each VLAN. Go to the router interface configuration page and configure each interface with an IP address that is in the same subnet as the VLAN interface that it connects to. For example, if Interface 1 has IP address 10.0.1.1, then the router interface that connects to Interface 1 should have an IP address in the 10.0.1.0/24 subnet.

With these configurations in place, hosts on each VLAN should be able to communicate with each other through the router, and you should have InterVLAN routing set up on your Sangfor device.