Hi,

we have Sangfor HCI v. 6.7.0 I need to forward task log to a syslog server.
Is it possible? I've enabled this option and I've checked the connectivity to syslog server and all is fine but logs don't arrive.


Many thanks in advance.
Oliver

rivsy has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

You can enable Syslog Server just go to:
Menu > System > Logs and Alarms > Syslog Server

syslog.png (33.19 KB, Downloads: 454)

syslog.png
Is this answer helpful?
Faisal Piliang Posted 10 Mar 2023 23:29
  
Page/tab name example: Navigate to Storage to enter the Storage configuration page. Parameter example: IP Address: Specifies the IP address
rivsy Lv5Posted 13 Mar 2023 09:37
  
You can enable Syslog Server just go to:
Menu > System > Logs and Alarms > Syslog Server

syslog.png (33.19 KB, Downloads: 454)

syslog.png
Jhazz Lv3Posted 13 Mar 2023 09:54
  
Yes it is possible to do just go to the Syslog Server tab then enabled it and input the server address and port of it
HeavT Lv2Posted 13 Mar 2023 10:36
  
Please see below video for configuration

JJ Lv2Posted 13 Mar 2023 11:28
  
Did you check if the server IP and ports are correct in the configuration?
Imran Tahir Lv4Posted 13 Mar 2023 12:24
  
Menu > System > Logs and Alarms > Syslog Server

Follow these setps

FoxR Lv2Posted 13 Mar 2023 13:17
  
click the "Syslog Server" then manually fill all the requirements there
Abdul Sami Lv2Posted 13 Mar 2023 13:56
  
Yes, it's possible to forward task logs from Sangfor HCI to a syslog server. Here are the steps to configure this feature:

  • Configure the Syslog server: First, you need to configure the Syslog server to accept logs from Sangfor HCI. Check that the syslog server is listening on the appropriate port (usually port 514) and that it is configured to accept logs from the Sangfor HCI.
  • Enable syslog forwarding in Sangfor HCI: In the Sangfor HCI web interface, navigate to System > Syslog and enable syslog forwarding. Enter the IP address of the syslog server and the port number for the syslog server.
  • Select the log level to be forwarded: Under the syslog forwarding section, select the log level you want to forward to the syslog server.
  • Save and test the configuration: Save the configuration and test it by generating a task log in the Sangfor HCI. Check the syslog server to ensure that the log has been forwarded successfully.

If you have enabled syslog forwarding and checked connectivity to the syslog server but logs are not arriving, you should check the following:
  • Firewall settings: Ensure that the firewall is not blocking traffic to the syslog server.
  • Log level: Check that the log level you selected for forwarding is appropriate and that the log is being generated at that level.
  • DNS resolution: If you are using a hostname for the syslog server, ensure that DNS resolution is working correctly.
  • Configuration errors: Double-check the configuration settings to ensure that there are no errors.


If none of these solutions work, you should consult the Sangfor HCI documentation or contact Sangfor support for further assistance.
April Men Lv1Posted 13 Mar 2023 16:13
  
Last edited by April Men 13 Mar 2023 16:14.

in the syslog server tab set the parameters with the same syslog server config

I Can Help:

Change

Moderator on This Board

2
20
0

Started Topics

Followers

Follow

Board Leaders