Sangfor NGAF reset

Newbie327164 Lv1Posted 27 Jul 2022 15:46

How do you factory reset a Sangfor NGAF?
Password forgotten.

jetjetd has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

Hello have you tried the steps below?

1. Connect to NGAF with firmware updater.
2. Press F10, and choose the Restore Factory Defaults.
Is this answer helpful?
jetjetd Lv4Posted 27 Jul 2022 15:55
  
Hello have you tried the steps below?

1. Connect to NGAF with firmware updater.
2. Press F10, and choose the Restore Factory Defaults.
RegiBoy Lv3Posted 27 Jul 2022 16:02
  
You can reset it with USB/Flashdrive.

1. Create an empty text file named reset-password.txt in the root directory of U Disk ( Directly in the USB)
2. Insert the USB drive to either USB ports of NGAF at front side where are eth ports and then restart your NGAF.
3. When the NGAF can normally log on to the Web User Interface, pull out the USB Drive.
4. See the results of the USB drive file reset-password.txt, If the recovery is successful, record the restored password in the file. (logs in file created) , otherwise the log is recorded the recovery failure information as unsuccessful.

Source: https://community.sangfor.com/archiver/?tid-1884.html
Adonis001 Lv1Posted 28 Jul 2022 08:33
  
You must connect to a Updater and after that press F10 then select Restor defaults
Noah19 Lv2Posted 28 Jul 2022 10:10
  
Try to hard reset.

- You can use a cross cable to restore factory defaults except by Updater,
Steps:
1. Using the power button to shutdown the IAM device.
2. Prepared a cross cable.
3. Using the cross cable to connect to any two interfaces of  IAM device。(Attention: The two interface can't be bypass interfaces.)
4. Finally starting up the IAM device and waiting for 5 minutes.
Imran Tahir Lv3Posted 30 Jul 2022 14:17
  
You can use a cross cable to restore factory defaults except by Updater,
Steps:
1. Use the power button to shut down the IAM device.
2. Prepared a cross cable.
3. Using the cross cable to connect to any two interfaces of the IAM device。(Attention: The two interface can't be bypass interfaces.)
4. Finally starting up the IAM device and waiting for 5 minutes.
rivsy Lv3Posted 01 Aug 2022 15:12
  
1. Create an empty text file named reset-password.txt in the root directory of U Disk ( Directly in the USB)
2. Insert the USB drive to either USB ports of NGAF at front side where are eth ports and then restart your NGAF.
3. When the NGAF can normally log on to the Web User Interface, pull out the USB Drive.
4. See the results of the USB drive file reset-password.txt, If the recovery is successful, record the restored password in the file. (logs in file created) , otherwise the log is recorded the recovery failure information as unsuccessful.
Imran Tahir Lv3Posted 01 Aug 2022 15:58
  

You can use a cross cable to restore factory defaults except by Updater,
Steps:
1. Use the power button to shut down the IAM device.
2. Prepared a cross cable.
3. Using the cross cable to connect to any two interfaces of the IAM device。(Attention: The two interface can't be bypass interfaces.)
4. Finally starting up the IAM device and waiting for 5 minutes.
kmrnliaqat Lv2Posted 01 Aug 2022 16:08
  

You can use a cross cable to restore factory defaults except by Updater,
Steps:
1. Use the power button to shut down the IAM device.
2. Prepared a cross cable.
3. Using the cross cable to connect to any two interfaces of the IAM device。(Attention: The two interface can't be bypass interfaces.)
4. Finally starting up the IAM device and waiting for 5 minutes.
Faisal P Lv8Posted 01 Aug 2022 21:21
  
Connect to NGAF with firmware updater. 2. Press F10, and choose the Restore Factory Defaults

I Can Help:

Change

Moderator on This Board

1
82
3

Started Topics

Followers

Follow

Board Leaders