pbeugenio Lv2Posted 2025-Jan-13 15:19
  
Q1: three (3) times

Q2: HCI6.1.0

Q3: yes, add node first

Q4: HCI6.8.0

Q5: No Limit

Q6: starting from HCI 6.0.0 it does not need any configuration on the switch, but in older version it must be connected to stack switch
CLELUQMAN Lv4Posted 2025-Jan-13 16:52
  
Q1 : The same USB KEY can only be used three times in different clusters.
Q2 : Starting from HCI6.1.0, the virtual key is supported for licensing.
Q3 : Yes, It is required to add the node into cluster first before licensing for new deployment of HCI6.8.0 cluster.
Q4 : Starting from HCI6.8.0, the licensing structure for virtual key has been changed.
Q5 : No Limit
Q6 : Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”
Newbie877525 Lv1Posted 2025-Jan-13 17:35
  
Q1: 3
Q2: HCI6.1.0
Q3: Yes
Q4: HCI6.8.0
Q5: No Limit
Q6: Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”
-        Select the physical interface and input the VLAN ID
-        IP address/netmask/gateway of VLAN interface are optional
pmateus Lv3Posted 2025-Jan-13 18:00
  
Q1: three times in different clusters
Q2: HCI6.1.0
Q3: Yes
Q4: HCI6.8.0
Q5: No Limit
Q6:Start from version 6.0.0, it support VLAN tagging for the link aggregate interface; Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”;Select the physical interface and input the VLAN ID;
IP address/netmask/gateway of VLAN interface are optional
Enrico Vanzetto Lv4Posted 2025-Jan-13 22:30
  
Q1:The same USB KEY can only be used three times in different clusters. After more than three times, using the KEY in the fourth HCI cluster will not activate the authorization.
Q2:Starting from HCI6.1.0, virtual key is supported for licensing
Q3:Yes, it is required to add the node into cluster first before licensing for new deployment of HCI6.8.0 cluster.
Q4:Starting from HCI6.8.0, the licensing structure for virtual key has been changed.
Q5:No limit
Q6:Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces” .Select the physical interface and input the VLAN ID .IP address/netmask/gateway of VLAN interface are optional
Rendy Rinaldy Lv1Posted 2025-Jan-14 12:01
  
Q1 : The same USB KEY can only be used three times in different clusters
Q2 : Starting from HCI6.1.0, virtual key is supported for licensing.
Q3 : yes, It is required to add the node into cluster first before licensing for new deployment of HCI6.8.0 cluster.
Q4 : Starting from HCI6.8.0, the licensing structure for virtual key has been changed.
Q5 : No Limit
Q6 : 1. Start from version 6.0.0, it support VLAN tagging for the link aggregate interface
2. Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”
3. Select the physical interface and input the VLAN ID
4. IP address/netmask/gateway of VLAN interface are optional
Apriyanto Lv5Posted 2025-Jan-14 15:45
  
Q1: How many times can be used for the same USB key in different clusters?
The same USB key can only be used three times in different clusters. After three uses, it will not activate authorization in a fourth cluster. However, there is no limit to the number of authorization updates in the same HCI cluster​.

Q2: Starting from which version, the virtual key can be supported for licensing?
Virtual keys are supported for licensing starting from HCI version 6.1.0​.

Q3: Is it required to add the node into a cluster first before licensing for a new deployment of HCI 6.8.0 cluster?
Yes, it is required to add the node into the cluster first before licensing for a new deployment of an HCI 6.8.0 cluster​.

Q4: Starting from which version, the licensing structure for the virtual key has been changed?
The licensing structure for the virtual key has been changed starting from HCI version 6.8.0​.

Q5: What is the number of Running VMs for the enterprise license edition?
There is no limit to the number of running VMs for the enterprise license edition​.

Q6: How to set up the VLAN for a link aggregate interface?
To set up VLAN for a link aggregate interface:
Navigate to Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces.
Select the physical interface and input the VLAN ID.
IP address, netmask, and gateway of the VLAN interface are optional​.
Ronnel Compayan Posted 2025-Jan-15 08:57
  
Q1. 3 times
Q2. HCI 6.1.0
Q3. Yes
Q4. HCI 6.1.0
Q5. No limit
Q6. ▪ In version 6.0.0, it support VLAN tagging for the link aggregate interface
▪ Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”
▪ Select the physical interface and input the VLAN ID
▪ IP address/netmask/gateway of VLAN interface are optional
Kbob Lv1Posted 2025-Jan-15 10:40
  
Q1 : three times in different clusters
Q2 : Starting from HCI6.1.0.
Q3 : yes, It is required to add the node into cluster first before licensing for new deployment of HCI6.8.0 cluster.
Q4 : Starting from HCI6.8.0,
Q5 : No Limit
Q6 : 1. Start from version 6.0.0, it support VLAN tagging for the link aggregate interface
2. Go to “Nodes > Physical Interfaces > Add Multiple VLAN Subinterfaces”
3. Select the physical interface and input the VLAN ID
4. IP address/netmask/gateway of VLAN interface are optional
belakios Lv1Posted 2025-Jan-16 11:04
  
This topic is only visible to the author.