Masyitoh Lv3Posted Feb-16-2025 23:50
  
Q1: Every physical node should maintain the same firmware and any required patches.
Q2: To incorporate nodes into a cluster, navigate to Nodes > Add New Node, assign a Cluster IP (preferably within the same subnet as the Management IP), and allow the system to detect Sangfor HCI nodes in the reachable network. If necessary, enable the SSH port under System > Port Management.
Q3: A is not the best answer.
Q4: Dedicated Mode is required for storage interfaces to prevent fluctuations in performance and bandwidth.
Q5: When the number of available physical interfaces is insufficient, Shared Mode helps repurpose Management, VXLAN, and Physical Edge connections.
Q6: Virtual datastores in a 3-node cluster cannot exceed 2.
salvo Lv2Posted Feb-16-2025 23:51
  
Q1: A common firmware version, including all necessary patches, should be used on all nodes.
Q2: To join nodes to a cluster, go to Nodes > Add New Node, configure the Cluster IP (it is advisable to use the same subnet as the Management IP), and let the system identify available Sangfor HCI nodes in the network. Enabling the SSH port under System > Port Management may be required.
Q3: The answer associated with A is incorrect.
Q4: Ensure storage interfaces function in Dedicated Mode to uphold bandwidth and performance stability.
Q5: Enable Shared Mode to conserve physical interface resources by reusing Management, VXLAN, and Physical Edge interfaces.
Q6: A 3-node cluster has a maximum of 2 virtual datastores available.
Surbakti Lv4Posted Feb-16-2025 23:51
  
Q1: The firmware version on all physical nodes must be the same, with any included patches.
Q2: When adding nodes to a cluster, visit Nodes > Add New Node, set the Cluster IP (ideally in the same subnet as the Management IP), and let the system automatically detect nodes running Sangfor HCI software. You may also need to activate the SSH port under System > Port Management.
Q3: The A option does not hold the correct answer.
Q4: Dedicated Mode is crucial for maintaining consistent storage interface performance and bandwidth.
Q5: In situations where physical interfaces are unavailable, Shared Mode provides a way to reuse Management, VXLAN, and Physical Edge interfaces.
Q6: A 3-node cluster is only capable of managing 2 virtual datastores.
reinaldo Lv2Posted Feb-16-2025 23:52
  
Q1: Firmware standardization across all physical nodes, including patches, is required.
Q2: To expand a cluster, go to Nodes > Add New Node, specify a Cluster IP (keeping it within the same subnet as the Management IP is recommended), and let the system locate reachable Sangfor HCI nodes. Enabling the SSH port in System > Port Management might be necessary.
Q3: A is mistakenly considered correct.
Q4: Activate Dedicated Mode to prevent performance and bandwidth variations in storage interfaces.
Q5: To ensure efficient network management, Shared Mode enables the repurposing of Management, VXLAN, and Physical Edge interfaces.
Q6: Only 2 virtual datastores can be assigned to a 3-node cluster.
dewa brain Lv2Posted Feb-16-2025 23:53
  
Q1: Identical firmware versions must be present on all physical nodes, including updates.
Q2: Adding nodes to a cluster requires accessing Nodes > Add New Node, entering the Cluster IP (best kept in the same subnet as the Management IP), and allowing the system to auto-detect Sangfor HCI nodes. Ensure the SSH port is enabled under System > Port Management if needed.
Q3: The answer corresponding to A is incorrect.
Q4: Dedicated Mode is the best option for stable storage interface bandwidth and performance.
Q5: Shared Mode can be employed to optimize the use of Management, VXLAN, and Physical Edge interfaces when physical connections are scarce.
Q6: A 3-node cluster is limited to hosting 2 virtual datastores.
keniedi Lv3Posted Feb-16-2025 23:53
  
Q1: A consistent firmware version, including patches, should be installed on all nodes.
Q2: To integrate nodes into a cluster, open Nodes > Add New Node, configure the Cluster IP (which should be within the same subnet as the Management IP), and let the system scan for Sangfor HCI nodes in the network. If required, activate the SSH port under System > Port Management.
Q3: Answer A should not be chosen.
Q4: Storage interfaces operate optimally with Dedicated Mode enabled for stable bandwidth and performance.
Q5: Enable Shared Mode to reuse Management, VXLAN, and Physical Edge interfaces when the number of physical interfaces is insufficient.
Q6: The system restricts a 3-node cluster to a maximum of 2 virtual datastores.
medho Lv2Posted Feb-16-2025 23:54
  
Q1: Every node must follow the same firmware update standard, including patches.
Q2: When adding a new node to a cluster, go to Nodes > Add New Node, assign the Cluster IP (recommended to be in the same subnet as the Management IP), and allow the system to find available Sangfor HCI nodes. The SSH port may need to be enabled in System > Port Management.
Q3: The given response A is not accurate.
Q4: Keep storage interfaces in Dedicated Mode to achieve uniform bandwidth and performance.
Q5: Use Shared Mode to repurpose Management, VXLAN, and Physical Edge interfaces when physical interfaces are limited.
Q6: A 3-node cluster reaches its virtual datastore limit at 2.
jenney Lv2Posted Feb-16-2025 23:54
  
Q1: All physical nodes should be running an identical firmware version, patches included.
Q2: To include additional nodes in a cluster, navigate to Nodes > Add New Node, specify a Cluster IP (keeping it within the same subnet as the Management IP is suggested), and let the system detect reachable Sangfor HCI nodes. The SSH port might need activation in System > Port Management.
Q3: The A selection is not correct.
Q4: Dedicated Mode should be activated for storage interfaces to maintain performance integrity.
Q5: Activate Shared Mode to allow Management, VXLAN, and Physical Edge interfaces to be reused in cases of limited physical interfaces.
Q6: With a 3-node cluster, the maximum virtual datastore count is 2.
zyrek Lv2Posted Feb-16-2025 23:55
  
Q1: Firmware synchronization across nodes, including any patches, is necessary.
Q2: To attach nodes to a cluster, access Nodes > Add New Node, configure the Cluster IP (preferably within the same subnet as the Management IP), and allow the system to detect Sangfor HCI nodes in the network. If necessary, enable the SSH port via System > Port Management.
Q3: The answer labeled A is not valid.
Q4: The use of Dedicated Mode on storage interfaces promotes steady performance and bandwidth.
Q5: When physical interfaces are in short supply, Shared Mode enables reuse of Management, VXLAN, and Physical Edge interfaces.
Q6: A 3-node cluster provides support for a maximum of 2 virtual datastores.
Riki Satria Lv3Posted Feb-16-2025 23:56
  
Q1: The same firmware build must be maintained across all physical nodes, including patches.
Q2: Adding nodes to a cluster involves selecting Nodes > Add New Node, setting the Cluster IP (recommended to be in the same subnet as the Management IP), and letting the system find Sangfor HCI nodes within the network. Enabling the SSH port under System > Port Management may be required.
Q3: The incorrect answer is A.
Q4: Dedicated Mode is key to ensuring storage interface performance and bandwidth remain stable.
Q5: Choose Shared Mode to optimize network resources by reusing Management, VXLAN, and Physical Edge interfaces when needed.
Q6: A 3-node cluster can function with a maximum of 2 virtual datastores.