Apriyanto Lv5Posted 2025-Jan-06 17:39
  
Q1: How to download the Sangfor aCloud(HCI) latest firmware?
You can download the latest Sangfor aCloud firmware from the official Sangfor Support Website or Partner Portal. A registered account with appropriate permissions is usually required.

Q2: What is the minimum USB drive capacity when you create bootable ISO firmware?
A. 4GB        B. 5GB        C. 6GB       D. 8GB
Answer: D. 8GB
An 8GB USB drive is the minimum capacity recommended to ensure there is enough space for the ISO file and additional configuration files.

Q3: What are the five steps needed to complete ISO Writing Steps?
Download the ISO file from the Sangfor official website.
Insert the USB drive into your computer.
Open the ISO writing tool (e.g., Rufus, Etcher).
Select the ISO file and USB drive, then start the writing process.
Safely eject the USB after the writing is completed.

Q4: Which of the following options is not the default login account to Access aServer IPMI?​
A. ADMIN/1111111           B. Sangfor/ADMIN
C. admin/admin               D. admin/admin1​
Answer: B. Sangfor/ADMIN
This is not a default login credential for accessing aServer IPMI.

Q5: What is the HCI Default MTU value?
Answer: 1500 bytes
The default MTU (Maximum Transmission Unit) value in Sangfor HCI is typically 1500, which is standard for Ethernet networks. Jumbo frames (MTU 9000) can be configured if needed.

Q6: What is the maximum number of interfaces that can be configured as a single port channel starting from HCI v6.0.0?
Answer: 8 interfaces
Starting from Sangfor HCI v6.0.0, a maximum of 8 interfaces can be grouped into a single port channel for link aggregation.
Enrico Vanzetto Lv4Posted 2025-Jan-06 20:56
  
Q1ownload at http://community.sangfor.com/plu ... &fid=47#/12/all
Select the aCloud(HCI) ISO image to download
Q2:A
Q3:1. Prepare the latest aCloud(HCI) ISO image & UltraISO application, 2. Launch the UltraISO & open aCloud(HCI) ISO Image, 3. Click Bootable > Write Disk Image…, 4. Select verify option and start to write, 5. Wait for Successful burn message
Q4:A
Q5:1500
Q6:8
pmateus Lv3Posted 2025-Jan-07 00:15
  
Q1: Download at http://community.sangfor.com/plu ... &fid=47#/12/all  and Select the aCloud(HCI) ISO image to download
Q2: A.
Q3: 1. Prepare the latest aCloud(HCI) ISO image & UltraISO application; 2. Launch the UltraISO & open aCloud(HCI) ISO Image; 3. Click Bootable > Write Disk Image…; 4. Select the following options and start to write; 5. Successful burn message
Q4: A.
Q5: 1600
Q6: 8 interfaces
pbeugenio Lv2Posted 2025-Jan-07 09:03
  
Q1: Go to community.sagfor.com and select aCloud(HCI) ISO image

Q2: A

Q3: 1.Prepare the latest aCloud(HCI) ISO image & UltraISO application
       2.Launch the UltraISO & open aCloud(HCI) ISO Image
       3.Click Bootable > Write Disk Image
       4.Select the following options and start to write
       5.Successful burn message

Q4: A

Q5: 1500

Q6: 8 interfaces
Newbie877525 Lv1Posted 2025-Jan-07 11:12
  
Q1: Login to Sangfor Community (https://community.sangfor.com). Go to Self Service > Download > Tools and click download on Sangfor HCI/SCP aDeploy.
Q2: A. 4GB
Q3:
-First, insert the USB flash disk into the personal PC, then open the software UltraISO, select File > Open, and load the ISO file of Sangfor HCI software from the local disk.
-Select Bootable > Write Disk Image and choose the USB drive into which you want to write the image file. Then, click the Write button and keep others' settings unchanged.
-The target of writing is USB flash disk or optical disc. Be sure to check Verify. The write method (usually USB-HDD+) is determined according to the USB startup type supported by the server.
-Insert the USB flash disk into the third-party server and boot from the USB flash disk in BIOS.
-Enable Virtualization Technology in BIOS, as shown below (Note: BIOS settings vary from computer to computer).
Q4: C. admin/admin               
Q5: 1500 bytes
Q6: 8 interfaces
ilham Lv2Posted 2025-Jan-07 11:27
  
Q1: Download at http://community.sangfor.com/plu ... &fid=47#/12/all
       Select the aCloud(HCI) ISO image to download
Q2: 4GB
Q3: 1. Prepare the latest aCloud(HCI) ISO image & UltraISO application
       2. Launch the UltraISO & open aCloud(HCI) ISO Image
       3. Click Bootable > Write Disk Image…
       4. Select the following options and start to write
       5. Successful burn message
Q4: A : ADMIN/1111111
Q5: 1600 MTU
Q6: 8 Interfaces
Humayun Ahmed Lv3Posted 2025-Jan-07 12:59
  
Q1: To download the Sangfor aCloud(HCI) latest firmware, follow these steps:

1. Go to the Sangfor community download link: http://community.sangfor.com/plu ... amp;fid=47#/12/all.
2. Select the aCloud(HCI) ISO image to download.

Q2: A. 4GB.

Q3: The five steps needed to complete the ISO Writing Steps are:

1. Prepare the latest aCloud(HCI) ISO image and UltraISO application.
2. Launch the UltraISO and open the aCloud(HCI) ISO image.
3. Click on Bootable > Write Disk Image….
4. Select the appropriate options and start to write.
5. Wait for the successful burn message.

Q4: A. ADMIN/1111111.

Q5: 1600.

Q6: 8.
Sangfor Alan Lv1Posted 2025-Jan-08 11:15
  
This topic is only visible to the author.
Noviyanto Lv3Posted 2025-Jan-08 12:43
  
Q1 : We can download at
        http://community.sangfor.com/plu ... &fid=47#/12/all
Q2 : A. 4GB
Q3 : 1. Prepare the latest aCloud(HCI) ISO image & UltraISO application
       2. Launch the UltraISO & open aCloud(HCI) ISO Image
       3. Click Bootable > Write Disk Image
       4. Select the following options and start to write
       5. Successful burn message
Q4 : A. ADMIN/1111111
Q5 : Default MTU size is 1600
Q6 : Maximum support configure 8 interfaces as single port channel.
Rendy Rinaldy Lv1Posted 2025-Jan-09 10:48
  
Q1 : 1. Download at http://community.sangfor.com/plu ... &fid=47#/12/all
2. Select the aCloud(HCI) ISO image to download

Q2 :  A. 4GB  

Q3 : 1. Prepare the latest aCloud(HCI) ISO image & UltraISO application
2. Launch the UltraISO & open aCloud(HCI) ISO Image
3. Click Bootable > Write Disk Image…
4. Select the following options and start to write
5. Successful burn message

Q4 : A. ADMIN/1111111  

Q5 : 1600 MTU

Q6 :  8 interfaces