Layer 2 Interface

Newbie628265 Lv1Posted 2024-Mar-25 13:10

Hi,

May I know if what type of interface can be added to layer 2 zone? Thanks.

1.route inteface
2.Virtual interface
3.vlan interface
4.mirror interface

Newbie517762 has solved this question and earned 20 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

HiHi,

In Sangfor NGAF, mirror interfaces cannot be added to layer 2 zones but other options are allowed.
Is this answer helpful?
Newbie517762 Lv5Posted 2024-Mar-26 10:42
  
HiHi,

In Sangfor NGAF, mirror interfaces cannot be added to layer 2 zones but other options are allowed.
mdamores Posted 2024-Mar-26 13:27
  
Hi,

The most suitable interface type to implement to a layer 2 zone is the VLAN interface. But the rest can be added to layer 2 zone except for the Mirror Interface
NCML985261 Lv2Posted 2024-Mar-26 13:52
  

In layer 2 zones, VLAN interfaces are typically used for network segmentation. While virtual interfaces and mirror interfaces have their uses, VLAN interfaces are the most common and relevant for this purpose. Route interfaces, primarily used for layer 3 routing, are less directly associated with layer 2 zoning.
Tayyab0101 Lv2Posted 2024-Mar-26 14:09
  
not possible to add mirror interface at layer2 level.
CLELUQMAN Lv4Posted 2024-Mar-26 14:57
  
LAYER 2
VLAN interface
Mirror interface

LAYER 3
Route interface
Virtual interface
Enrico Vanzetto Lv4Posted 2024-Mar-26 15:56
  
Hi, Sangfor NGAF supports both Layer 2 and Layer 3 interface types.

In a Layer 2 interface, the interface is similar to a common switch. It supports both IPv4 and IPv6 environments. There’s no need to configure an IP address, it doesn’t support route forwarding, and it forwards data according to the MAC address table.

In a Layer 3 interface, you can configure an IP address for the interface. This type of interface is used for routing and forwarding data based on IP addresses.

In general, a mirror interface (also known as a SPAN port) is used to forward copies of network packets from one interface to another, which is useful for network troubleshooting or for implementing network intrusion detection systems.

As i know, you can't add mirror interface to a layer 2 zone.
Newbie290036 Posted 2024-Mar-26 19:16
  
In a Layer 2 zone, VLAN interface can be added. VLAN interfaces are used to segment the network into virtual LANs, providing logical separation and isolation of traffic within a Layer 2 network. VLAN interfaces allow different VLANs to communicate with each other through routing or Layer 3 interfaces, while keeping the traffic segregated at Layer 2.
Zonger Lv5Posted 2024-Mar-26 19:23
  
All below interfaces can be added to Layer 2 zone

1. Route Interface
2. Virtual Interface
3. VLAN Interface
pmateus Lv2Posted 2024-Mar-26 20:15
  
Hi,
You can add the following interfaces: Route Interface, Virtual Interface, VLAN Interface

I Can Help:

Change

Moderator on This Board

11
8
5

Started Topics

Followers

Follow

1
3
6

Started Topics

Followers

Follow

0
4
5

Started Topics

Followers

Follow

67
20
3

Started Topics

Followers

Follow

3
14
3

Started Topics

Followers

Follow

1
139
3

Started Topics

Followers

Follow

Board Leaders