NGAF Load link balancing

Julius Lv1Posted 2022-Sep-08 13:37

Hi, Does anyone already implement wan link load balancing, round robin? Can you please guide me for configuration. Thanks folks

Newbie517762 has solved this question and earned 20 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

HiHi,

Please find the attched file for Configuration Guide & pls refer Chapter 6 - Link Load Balancing Route.

Configuration Step:
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located)
Step 3. Source IP (All)
Step 4. Destination IP group (All)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3
Step 7. Others can be kept as default Sample Configuration

I hope it can be help you, thanks.

SANGFOR_NGAF_v8.0.35_Policy-Based Routing Configuration.pdf (901.28 KB, Downloads: 758)
Is this answer helpful?
kmrnliaqat Lv3Posted 2022-Sep-22 19:41
  

Thank you very much for the information
Fida_Balti Lv4Posted 2022-Sep-20 13:49
  
thank you colleagues
Naomi Posted 2022-Sep-19 09:21
  
Configuration:
1) Enter the policy name (Any will do)
2) Zone of Origin (where the internal network user is located)
3) IP address of origin (All)
4) Group of destination IP addresses (All)
5) In the Application menu, select HTTP application.
6) Interaction (Select eth1 and eth2)
Others can be left as the default.
RegiBoy Lv5Posted 2022-Sep-19 09:11
  
Network >Route>Policy Based Route and configure your desire route
Rhebie Lv3Posted 2022-Sep-16 16:40
  
Please check the product version before continuing with the instructions because they are more accurate in version 8.0.35.
To avoid wasting bandwidth, employ the link-load balancing route.
Ashley Anne Lv2Posted 2022-Sep-16 16:37
  
Step 1. Name of the policy, please (Any will do)
Step 2. Source Area (where the internal network user is located)
Step 3. IP source (All)
Step 4. Destination IP assortment (All)
Step 5. In the Application, choose HTTP application.
Step 6. (Choose eth1 and eth 3 for the interface.
Step 7: The remaining items can be left in their normal configuration
Rashley Lv2Posted 2022-Sep-16 16:33
  
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located)
Step 3. Source IP (All)
Step 4. Destination IP group (All)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3
Step 7. Others can be kept as default Sample Configuration
arjay Lv3Posted 2022-Sep-16 13:47
  
Configuration Step:
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located/LAN)
Step 3. Source IP (All)
Step 4. Destination IP group (All/ANY/WAN)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3/WAN
jed Lv2Posted 2022-Sep-14 10:19
  

51262632139ec74321.png (31.05 KB, Downloads: 290)

51262632139ec74321.png

63705632139f798837.png (25.98 KB, Downloads: 284)

63705632139f798837.png

47908632139fb5cbee.png (25.98 KB, Downloads: 292)

47908632139fb5cbee.png
Arleng Lv2Posted 2022-Sep-14 08:57
  
Last edited by Arleng 14 Sep 2022 09:00.

Link load-balancing route

]
Outbound Interface เลือก Interface ขา Wan หรือ Link internet เข้ามา
Add Interface
Mode load-balancing

Route
Enable Link state Detection ที่ static route ขา WAN

Interface
Enable Link state Detection

I Can Help:

Change

Moderator on This Board

11
7
5

Started Topics

Followers

Follow

1
3
5

Started Topics

Followers

Follow

0
4
5

Started Topics

Followers

Follow

67
20
3

Started Topics

Followers

Follow

3
14
3

Started Topics

Followers

Follow

1
137
3

Started Topics

Followers

Follow

Board Leaders