Kbob Lv1Posted 2025-Jan-09 17:20
  
Q1 : 1. Download at https://community.sangfor.com/pl ... &fid=47#/12/all
2. Select the aCloud(HCI) ISO image to download.
Q2 :  A. 4GB.
Q3 : 1. Prepare the latest aCloud(HCI) ISO image & UltraISO application.
2. Launch the UltraISO & open aCloud(HCI) ISO Image.
3. Click Bootable > Write Disk Image…
4. Select the following options and start to write.
5. Successful burn message.
Q4 : A. ADMIN/1111111  
Q5 : 1600 MTU.
Q6 :  8 interfaces.
JJ Teoh Lv1Posted 2025-Jan-10 16:29
  
Q1)Download at Sangfor community or with the link of http://community.sangfor.com/plu ... &fid=47#/12/all
Q2) A. 4GB (more than 4GB)
Q3) Step1: Prepare the latest aCloud(HCI) ISO image & UltraISO application
Step 2: Launch the UltraISO & open aCloud(HCI) ISO Image
Step 3: Click Bootable > Write Disk Image…
Step 4: Select the following options and start to write
Step 5: Successful burn message
Q4) not in the selection as all ABCD was the default login account
Q5) 1500
Q6) 8 interfaces



ND Lv3Posted 2025-Jan-10 17:07
  
Q1: Go to https://community.sangfor.com/pl ... &fid=47#/12/all and download the firmware you require.

Q2: D

Q3: 1. Get latest UltraISO, Insert USB drive into PC.
2. Launch UltraISO.
3. Select File > Open and load ISO file of Sangfor HCI software from localdisk.
4. Select Bootable > Write Disk Image and choose the USB drive into which you want to write the image file. Then, click on Write button and keep others settings unchanged. You can remove the USB drive after the image file is written to the USB drive.
5. Enable Virtualization Technology in BIOS, asshown below (Note: BIOS settings vary from computer tocomputer).

Q4: D

Q5: 1500

Q6: 8
Zonger Lv5Posted 2025-Jan-10 19:15
  
1. To download the latest firmware for Sangfor aCloud (HCI), log in to the Sangfor support portal (https://support.sangfor.com), navigate to the "Downloads" section, and select the appropriate firmware version for your system.

2. A 4GB

3.
a) Obtain the ISO firmware or operating system image that you want to write to the USB drive.

b) Insert the USB drive into your computer and ensure it has a sufficient capacity (typically 4GB or more). Back up any important data, as the process will erase the drive.

c) Use a tool like Rufus, BalenaEtcher, or the built-in disk utility (for macOS or Linux) to write the ISO file to the USB drive.

d) Open the selected tool, then choose the downloaded ISO file and select the USB drive as the target device.

e) Start the Writing Process: Click the "Start" or "Write" button to begin the process. The tool will format the USB drive and copy the necessary bootable files from the ISO, making it ready to use as a bootable USB drive.

4.  B. Sangfor/ADMIN.

5.  1500 bytes

6. 16
alvaro Lv2Posted 2025-Jan-11 17:51
  
Q1: The most recent Sangfor aCloud firmware can be obtained from the official Sangfor Support Website or the Partner Portal, with access typically requiring a registered account and proper permissions.

Q2: D. 8GB

Q3: Download the ISO file from the Sangfor website, plug in your USB drive, open an ISO writing tool like Rufus or Etcher, choose the ISO and USB drive, and begin the process. Once done, eject the USB safely.

Q4: B. Sangfor/ADMIN

Q5: 1500 bytes

Q6: 8 interfaces
abinaya Lv2Posted 2025-Jan-11 18:47
  
Q1: To download the latest Sangfor aCloud firmware, visit the official Sangfor Support Website or Partner Portal, but note that a registered account with the necessary permissions is generally needed.

Q2: D. 8GB

Q3: First, download the ISO from the official Sangfor site, then insert your USB drive. Open an ISO tool (e.g., Rufus or Etcher), select the files, and begin writing. Once finished, safely eject the USB.

Q4: B. Sangfor/ADMIN

Q5: There is 1500 bytes

Q6: Answer is 8 interfaces
Andini Lv3Posted 2025-Jan-11 18:49
  
Q1: You can access the latest Sangfor aCloud firmware through the official Sangfor Support Website or Partner Portal, although a registered account with the appropriate permissions is usually a prerequisite.

Q2: D. 8GB

Q3: To start, download the ISO file from the Sangfor website, plug your USB into the computer, open a tool such as Rufus or Etcher, select the files, and initiate the process. Don’t forget to safely eject the USB once the process is completed.

Q4: B. Sangfor/ADMIN
Q5: There is 1500 bytes
Q6: Answer is 8 interfaces
Ketut Lv3Posted 2025-Jan-11 18:55
  
Q1: The latest version of Sangfor aCloud firmware is available for download on the official Sangfor Support Website or Partner Portal, but you will typically need a registered account and proper access rights.
Q2: D. 8GB
Q3: Begin by downloading the ISO file from the Sangfor website, then insert the USB drive. Open an ISO writing program like Rufus or Etcher, choose the ISO and USB drive, and start the writing process. When done, eject the USB drive safely.
Q4: B. Sangfor/ADMIN
Q5: There is 1500 bytes
Q6: Answer is 8 interfaces