This site uses cookies for functionalities and analytics. By continuing to use this site, you agree to this use. Learn more Close
Categories › General › User Contribution Center › #Configuration# Sangfor NSF SSL VPN configuration gu ...
#Configuration# Sangfor NSF SSL VPN configuration guide
  

Sangfor Jojo Lv5  Posted 14 May 2024 16:09


  
*Product: NSF
  
*Version: 8.0.85

  
*1. Introduction
  
1.1 User Scenario
  Nowadays, connecting to the corporate network from outside can be a challenge as the complexity of networks increases more and more. Furthermore, by connecting to public networks, traffic is often filtered and only the most common protocols for web browsing are allowed. This is where SSL VPN comes into play. This type of VPN uses the https protocol commonly used for web browsing and less subject to restrictions when connecting to public networks and also get data encryption to ensure security and data integrity. Below we see how to correctly configure the SSL VPN on Sangfor NSF.


  
1.2 Requirements
  1. Firewall Sangfor NSF firmware updated to the latest release
  2. A static public ip address on wan interface
  3. A client with Sangfor EasyConnect


  
*2. Configuration Guide
  
2.1 NGAF VPN SSL Configuration
  
2.1.1 NGAF VPN SSL Deployment mode
  Step 1. Define the interfaces that Sangfor SSL VPN must use.
  To do this you have to go to Network > SSL VPN > Deployment.
  On this guide we’ll see the gateway deployment node.
  On the next screen, you must select proprely ethernet interfaces on Sangfor NGAF (on this example, we have eth1 as wan and eth2 as Layer 3 Lan):

  
  After that, you can select the port of web ui ssl vpn portal.
  You can achieve it by going to Network > SSL VPN > Login Options.
  Enable only TLS 1.2 for security reasons.


  
  2.1.2 NGAF VPN SSL resource creation
  Now, you can create a resource group to keep together all your resources.
  To create it, you must go to Network > SSL VPN > Resources and create a resource group (on this example I named it mycompany)




  
  
  Now on the same page, we can define the internal network as resource by creating an L3VPN App and insert your network details as follows (on our example we have 10.0.0.0/22 as internal network). Don’t forget to specify the resource group created before.



  
  
  On L3VPN App mode, the VPN client will install a virtual network card to route all traffic into it (any protocols).


  2.1.3 NGAF VPN SSL user creation
  Now on this web UI path we can choose to create a local user or import a user list from an external source (you must configure it first on Sangfor NGAF)
  Network > SSL VPN > Local Users
  On this example we choose to create a local user named testuser.




  
  
  2.1.4 NGAF VPN SSL role assignment
  At this stage, we must assign a role to the newly created user to associate them with resources.
  To do it, you must go to Network > SSL VPN > Roles and assign a role.
  On our example we’ll create a new role to grant testuser connect to the resources that stands on resource group that we create before (named mycompany)





  
  2.1.5 NGAF VPN SSL virtual IP pool
  On the following section, we’ll see which ip range to assign to vpn ssl users that connects from external by using Sangfor VPN SSL.
  For a specific resource group you can define a virtual ip range to use.
  By default, there is 2.0.1.1 - 2.0.1.254 virtual ip range to all resources group.
  I recommend to not delete this default virtual ip range.




  
  2.1.6 NGAF VPN SSL login page
  Make sure the users can reach the NSF port 4430(SSLVPN default port) from external networks, by typing the public ip with port on a browser(https://x.x.x.x:4430).

             
  

As you can see, the web page will prompt you to install Sangfor EasyConnect client on your pc.
  After installation, you can log in to the SSLVPN and you are connected.
  After login, you can check on the web page the resources you can connect to.


  
*3. Precaution
  When external users want to connect to intranet resources by using Sangfor VPN SSL, it’s important to check that the external user’s local network doesn’t overlap with the virtual ip pool or intranet network.



This article is written by Enrico Vanzetto who is a tehnical engineer and has much experience and a better understanding of Sangfor network secure (NGAF), HCI, Endpoint Secure, VDI, and Cyber Command products. If you want to know more about him, click here.

4_Sangfor NGAF SSL VPN configuration guide_Enrico_EN.pdf

631.77 KB, Downloads: 233

Like this topic? Like it or reward the author.

Creating a topic earns you 5 coins. A featured or excellent topic earns you more coins. What is Coin?

Enter your mobile phone number and company name for better service. Go
Sangfor Jojo Lv5  Posted 14 May 2024 16:11
  
Congratulations on getting 4000 coins.

If you want to share articles like troubleshooting cases or configuration guides, please click the link below to register for this event.

Trending Topics

Board Leaders